Technical Discussion
  >> DSL Hardware Discussion


Register (or login) on our website and you will not see this ad.


Pages in this thread: 1 | [2] | 3 | 4 | (show all)   Print Thread
Standard User 4M2
(experienced) Mon 06-Aug-12 15:45:04
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
This might be useful http://support.zen.co.uk/kb/Knowledgebase/SpeedTouch... smile
Standard User MHC
(legend) Mon 06-Aug-12 15:58:09
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
Without access to a device, I can't go any further.

What you are trying to do is STOP the 780 allocating the IP addresses to any device and allowing the other hub to do so.

In the CLI the instruction would be something like: dhcp server config state = disabled or dhcp server config state = disabled


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

M H C


taurus excreta cerebrum vincit
Standard User athegn
(member) Mon 06-Aug-12 16:06:18
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: MHC] [link to this post]
 
MHC

Thank you anyway.


Register (or login) on our website and you will not see this ad.

Standard User athegn
(member) Mon 06-Aug-12 16:21:27
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: 4M2] [link to this post]
 
Thank you

But when I login into 192.168.1.254 I do not get a start up sequence - 10.0.0.138 does not login.
Standard User BatBoy
(legend) Mon 06-Aug-12 16:25:17
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
You should see the Speedtouch Homepage. Click Speedtouch, then click Pick a Task and then Set-up.


_____________________________________________________________________________________________ this is not usenet __________________
Standard User athegn
(member) Mon 06-Aug-12 16:28:48
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
Found this in CLI manual

dhcp server config [state = <{ disabled / enabled } >]

tried typing that in a command prompt box got the message 'dhcp' is not recognised etc

Typed in:-

dhcp server config = disabled
Standard User 4M2
(experienced) Mon 06-Aug-12 17:35:51
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
Not sure how you telnet the Speedtouch 780 WL but did you initially use:

telnet 192.168.1.254

then enter Username and Password?
Standard User MHC
(legend) Mon 06-Aug-12 17:36:00
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: athegn] [link to this post]
 
Speedtouch originally used the 10.0.0.xxx private IP range but followed the sheep when most other started using 192.168.1.xxx you need to know which block yours is using.


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

M H C


taurus excreta cerebrum vincit
Standard User MHC
(legend) Mon 06-Aug-12 17:38:08
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: 4M2] [link to this post]
 
That should be OK for his ST ... it will come up with a very login screen - reminiscent of an ASCII drawing! and then requests Name and Password.


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

M H C


taurus excreta cerebrum vincit
Standard User 4M2
(experienced) Mon 06-Aug-12 18:06:40
Print Post

Re: Wired and Wireless access from an ethernet port.


[re: MHC] [link to this post]
 
Yep, that's what I get with a tg585v7 but haven't checked how to disable DHCP since the commands may be quite different for a Speedtouch 780 WL...
Pages in this thread: 1 | [2] | 3 | 4 | (show all)   Print Thread

Jump to