If you mean you are now using an unlocked HG612, then the GUI stats are not completely trustworthy.

The sync speeds are correct, but compare with the telnet ones:-

GUI
Attainable rate (kbit/s) 59808 16107
SNR margin (dB) 19.7 0
Line attenuation (dB) 13.6 7.4
Output power (dBmV) 13.6 7.4

Line rate (kbit/s) 59997 15142 0 0
CRC errors 254 127 18 0
FEC errors 0 0 0 0
HEC errors 122 4294967290 32 0

TelnetLogin:admin
Password:
ATP>sh

BusyBox v1.9.1 (2014-01-21 16:44:38 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# xdslcmd info --show
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 16062 Kbps, Downstream rate = 59812 Kbps
Bearer: 0, Upstream rate = 15142 Kbps, Downstream rate = 59997 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 5.9 6.5
Attn(dB): 19.7 0.0
Pwr(dBm): 13.6 7.4
VDSL2 framing
Bearer 0
MSGc: -6 25
B: 243 237
M: 1 1
T: 0 64
R: 10 16
S: 0.1295 0.5000
L: 15691 4064
D: 8 1
I: 254 127
N: 254 254
Q: 8 0
V: 0 0
RxQueue: 48 0
TxQueue: 16 0
G.INP Framing: 18 0
G.INP lookback: 16 0
RRC bits: 0 24
Bearer 1
MSGc: 122 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 8.0000 0.0000
L: 32 0
D: 1 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 1978626
OHFErr: 13 400
RS: 3020515448 1004302
RSCorr: 6409885 4044
RSUnCorr: 0 0
Bearer 1
OHF: 171234552 0
OHFErr: 0 0
RS: 1369875922 0
RSCorr: 343 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 137193 0
rtx_c: 189529 0
rtx_uc: 98116 0

G.INP Counters
LEFTRS: 2465 0
minEFTR: 59993 0
errFreeBits: 3142817269 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 3808555439 0
Data Cells: 393989148 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 118 864
SES: 38 1
UAS: 333 311
AS: 2750516

Bearer 0
INP: 48.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 0.00 8.03
OR: 0.01 30.87
AgR: 60058.37 15172.73

Bearer 1
INP: 2.00 0.00
INPRein: 2.00 0.00
delay: 0 0
PER: 16.06 0.01
OR: 63.75 0.01
AgR: 63.75 0.01

Bitswap: 2110296/2110296 13425/13449

The GUI SNR contains the attenuation, the attenuation contains the power, and the power is correct.

IIRC there are odd things also going on with the error stats, but I haven't looked to compare in detail.

Edited by RobertoS (Mon 30-Nov-15 23:22:03)

This is what I am getting, guessing I lost a little on the downstream when I swapped out the ECI as the max attainable according to BT OR engineer was 69Mbps:


Downstream Upstream
Attainable rate (kbit/s) 67892 27670
SNR margin (dB) 6.6 9.3
Line attenuation (dB) 15.1 0
Output power (dBmV) 12.7 4.3


# xdslcmd info --show
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 28496 Kbps, Downstream rate = 67660 Kbps
Bearer: 0, Upstream rate = 20000 Kbps, Downstream rate = 67660 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 6.5 10.0
Attn(dB): 15.1 0.0
Pwr(dBm): 12.7 4.3
VDSL2 framing
Bearer 0
MSGc: 18 150
B: 239 236
M: 1 1
T: 21 5
R: 0 16
S: 0.1129 0.3771
L: 17008 5410
D: 1 1
I: 240 255
N: 240 255
Counters
Bearer 0
OHF: 3470719 1011102
OHFErr: 29 6
RS: 0 1264641
RSCorr: 0 67
RSUnCorr: 0 0

Bearer 0
HEC: 42 0
OCD: 0 0
LCD: 0 0
Total Cells: 805653551 0
Data Cells: 50278300 0
Drop Cells: 0
Bit Errors: 0 0

ES: 21 6
SES: 0 0
UAS: 104 104
AS: 6195

Bearer 0
INP: 0.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 1.78 6.15
OR: 107.56 202.87
AgR: 67767.28 20203.27

Bitswap: 3709/3709 29/30

That's interesting. I wonder if there's been an update that I haven't noticed, correcting the GUI. I shall look into that another day if I remember.

If you see the Bearer 1 stuff that I have then G.INP is active. I doubt if you will need it though.

Our cab is an ECI so I won't hold my breath for G.INP to be switched on any time soon