Ryan's suggestion is easier

I would provide links but I don't have one for balds but here is DSLStats.

http://www.s446074245.websitehome.co.uk/

Used the DSLStats tool seemed easier - one thing though, I can get stats with laptop connected direct to LAN2 but if I connect LAN2 to one of the four router (belkin F6D6230) LAN ports then I can no longer 'see' the modem? This means I can't easily monitor 24/7 I can only get snapshots by taking the laptop to the modem for a brief direct connection.

Speedtest.net shows I've recovered from the 24meg ceiling to 33meg which is the same pattern last time I did P2P so would be back to 38meg within a week or so. Anyways here are my stats, are they er good/bad/normal?. I guess what I really need to do is wait till I'm back to full speed then run DSLStats whilst actually P2Ping?

xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Max: Upstream rate = 25199 Kbps, Downstream rate = 84008 Kbps
Path: 0, Upstream rate = 1999 Kbps, Downstream rate = 34995 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 27.7 30.1
Attn(dB): 0.0 0.0
Pwr(dBm): 13.0 -0.7
VDSL2 framing
Path 0
B: 237 31
M: 1 2
T: 64 36
R: 16 16
S: 0.2164 0.9922
L: 9392 645
D: 1 1
I: 254 80
N: 254 80
Counters
Path 0
OHF: 21143294 475439
OHFErr: 51 0
RS: 1353152423 4128615
RSCorr: 13429 3
RSUnCorr: 174 0

Path 0
HEC: 135 0
OCD: 10 0
LCD: 10 0
Total Cells: 649328665 0
Data Cells: 101452924 0
Drop Cells: 0
Bit Errors: 0 0

ES: 29 0
SES: 0 0
UAS: 70 70
AS: 73478

Path 0
INP: 0.00 0.00
PER: 3.46 13.39
delay: 0.00 0.00
OR: 69.33 57.33

Bitswap: 3 590

Total time = 20 hours 26 min 47 sec
FEC: 13429 0
CRC: 51 0
ES: 29 0
SES: 0 0
UAS: 70 70
LOS: 0 0
LOF: 0 0
Latest 15 minutes time = 11 min 47 sec
FEC: 3 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 5 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
Latest 1 day time = 20 hours 26 min 47 sec
FEC: 13429 0
CRC: 51 0
ES: 29 0
SES: 0 0
UAS: 70 70
LOS: 0 0
LOF: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
Since Link time = 20 hours 24 min 37 sec
FEC: 13429 3
CRC: 51 0
ES: 29 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
#

What's the ip address of your LAN and the ip address of LAN2? There may be a conflict.

Looks like you are on a "40 down / 2 up" package.

If he is on a 40 meg package wouldn't his sync be 40 given his attainable, even with interleaving?

Edited by R0NSKI (Fri 14-Jun-13 13:29:02)

Correct ronski, seems to be some banding going on.

What IP do you use to access the belkin?

2 US and 35 DS, are you on a 40/2 package? (doubtful)

Edited by ryant704 (Fri 14-Jun-13 13:32:52)

In reply to a post by ryant704:

Correct ronski, seems to be some banding going on.

What IP do you use to access the belkin?

2 US and 35 DS, are you on a 40/2 package? (doubtful)

The lower Talktalk Fibre package is 40/2.

Yes I'm on TT 40/2 package. As I say I normally get 38meg (as measured by any of the usual speedtesters), following the P2P session it fell to 24meg, but it's back up to 33meg now - which would fit with a 34995 banding (set by DLM?)

I access the belkin via http://192.168.2.1/
the modem via http://192.168.1.1/

The bottom right corner of the DSLStats interface says Interleave:OFF, though the stats page says Interleave depth: 1

In reply to a post by Alexir:

I access the belkin via http://192.168.2.1/
the modem via http://192.168.1.1/

The bottom right corner of the DSLStats interface says Interleave:OFF, though the stats page says Interleave depth: 1

The modem and router are on different sub nets, the first three numbers need to be the same, the fourth needs to be unique. Login in to the modem and change the IP to 192.168.2.254, hopefully that IP is not in use, you could also stop it being issued by changing the ip range in the router so it only uses up to 253.

When you've changed the IP you can plug it back into the router.

Edit: Interleaving depth of 1 is off

Max: Upstream rate = 25199 Kbps, Downstream rate = 84008 Kbps
Path: 0, Upstream rate = 1999 Kbps, Downstream rate = 34995 Kbps

You have an attainable speed of 84 meg, this is what the modem thinks your line is capable of, so your sync speed (path above) should be 39999 kbps, it looks like your line has been banded for whatever reason.

It would be good if you could have Bald Eagles script running 24/7 for a while, it is really easy to setup if running windows - let me know if you need any help - I wrote the editor part which sets up all the options easily.

Edited by R0NSKI (Fri 14-Jun-13 21:13:58)

You shouldn't use 255 as an IP. The last address of a subnet is reserved as the broadcast address.

I've edited my post to save any confusion/problems.

Now you mention it when I tried to use 255 in the past my router wouldn't let me, so that explains it, thanks.