Stats interpretation - please.

Stats from HG612 below, it doesn't look like G.IMP is active. Engineer coming later this week since I am only about 250m from the AIO (new estate) and theoretically should be getting 80/20 (understand of course theres an overhead) but only getting around 46. BT though it was strange that upload was pretty much full speed but not the download.

Anyone spot anything unusual in the stats below if you have a sec ?
Thanks.


# xdslcmd info --show
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 24448 Kbps, Downstream rate = 52952 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 50219 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 7.1 8.5
Attn(dB): 14.6 0.0
Pwr(dBm): 13.1 6.4
VDSL2 framing
Bearer 0
MSGc: 18 26
B: 239 237
M: 1 1
T: 64 42
R: 14 16
S: 0.1521 0.3781
L: 13360 5374
D: 1 1
I: 254 127
N: 254 254
Counters
Bearer 0
OHF: 45964883 2930380
OHFErr: 1173 1634
RS: 2941726361 2426971
RSCorr: 20688 4983
RSUnCorr: 4864 0

Bearer 0
HEC: 2644 0
OCD: 93 0
LCD: 93 0
Total Cells: 2247977443 0
Data Cells: 409512190 0
Drop Cells: 0
Bit Errors: 0 0

ES: 3200 3531
SES: 11 0
UAS: 56 45
AS: 112295

Bearer 0
INP: 0.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 2.44 3.98
OR: 78.59 64.22
AgR: 50298.01 20063.54

Bitswap: 64421/64421 753/753

Additional stats.

xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 24440 Kbps, Downstream rate = 52952 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 50219 Kbps

Discovery Phase (Initial) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3959)
Medley Phase (Final) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3959)
VDSL Port Details Upstream Downstream
Attainable Net Data Rate: 24440 kbps 52952 kbps
Actual Aggregate Tx Power: 6.4 dBm 13.1 dBm
====================================================================================
VDSL Band Status U0 U1 U2 U3 U4 D1 D2 D3
Line Attenuation(dB): 3.7 16.3 22.8 N/A N/A 9.7 20.9 30.6
Signal Attenuation(dB): 3.7 15.4 21.9 N/A N/A 12.4 20.7 30.5
SNR Margin(dB): 8.4 8.5 8.4 N/A N/A 7.1 7.1 7.1
TX Power(dBm): -8.8 -25.9 6.4 N/A N/A 9.8 7.8 6.9

In reply to a post by Pgre:

VDSL Band Status U0 U1 U2 U3 U4 D1 D2 D3
Line Attenuation(dB): 3.7 16.3 22.8 N/A N/A 9.7 20.9 30.6

Are u sure of within 250m away from the cabinet? Your stats are look like you are approx 350m away!

Mine is much closer to the cabinet approx 250m below:

VDSL Band Status U0 U1 U2 U3 U4 D1 D2 D3
Line Attenuation(dB): 2.6 12.8 19.2 N/A N/A 6.7 15.1 24.7

What estimate does www.dslchecker.bt.com give for the line?

I can see it's a Huawei cab but G.INP is not on.

Hi,

As mentioned 80/20 and yes, I can see G.INP isn't on as no Bearer info.

What firmware is on your openreach modem HG612?

Sorry, that's not an estimate returned by the dslchecker.

I meant like this :

VDSL Range A (Clean) 80 69.6 20 20 63.1 Available -- -- --
VDSL Range B (Impacted) 80 55 20 17.8 39.8 Available -- -- --

It's based on the chap that pulled my line through and the raft of engineers I have spoken who did the AIO install, and all have said its its around 250 to 300m worst case.

At .3km BT expect around 76 less the overhead.

Just for info, I was previously getting around 28Mbps when the line was 1.3k to the old PCP, which meant it seemed to be performing better than normally expected. (normal estimates are around 23 for that distance)

Well.. 80/20 is what I suggested..

High Low High Low
VDSL Range A (Clean) 80 80 20 20 76.4
VDSL Range B (Impacted) 80 63.7 20 17.6. 39.8

B030SP08