Is my connection banded

Hi all quick question is my line on a banded profile?:

ATU-R Information
Type: VDSL2
Hardware: Annex A
Firmware: 05-07-06-0D-01-07
Power Mngt Mode: DSL_G997_PMS_L0
Line State: SHOWTIME
Running Mode: 17A
Vendor ID: b5004946 544e0000
ATU-C Information
Vendor ID: b5004244 434da48c [BDCM]
Line Statistics

Downstream Upstream
Actual Rate 48999 Kbps 7323 Kbps
Attainable Rate 60806 Kbps 7323 Kbps
Path Mode Fast Fast
Interleave Depth 1 1
Actual PSD 5. 8 dB 13. 3 dB
Near End Far End
Trellis ON ON
Bitswap ON ON
ReTx 0 1
SNR Margin 5 dB 6 dB
Attenuation 23 dB 34 dB
CRC 189 24505
FECS 0 s 4196 s
ES 43 s 23020 s
SES 7 s 0 s
LOSS 0 s 0 s
UAS 29 s 3100 s
HEC Errors 0 0
RS Corrections 0 0
LOS Failure 0 0
LOF Failure 0 0
LPR Failure 0 0
NCD Failure 0 0
LCD Failure 0 0
NFEC 240 32
RFEC 16 16
LYSMB 1977 16

Appears so.

What happens if you do a resync or modem reboot? Just one, initiated by turning power OFF, wait a few minutes, disconnected lead, reboot, wait a few minutes and reconnect. Then leave it alone

Darn funny stats presentation, and some of the figures.

What are all the "s" symbols against things that are nothing to do with seconds; apparently banded as you say but:-

a low SNRM;
FECs from where, on Fast Path;
huge ES (downstream? as often those are the opposite way round to sync speeds, SNRM and attenuation) yet zero ES in the same direction;
up attenuation only a fraction below down, though this does sometimes happen, (I'm making the same assumption about directions).

I forget what UAS is. The zeros lower down are expected. The bottom three line are what?

I wonder what the modem is.

I have rebooted it a few times and it always connects at this sync rate, had a power cut over four months ago and when the power came back on my router reconnected at a higer sync rate 60mb (its never connected at that) but the error rate was so high it did a resync to what it is today.

its a draytek 2860 modem these stats are a cut and paste from the GUI.

If it always syncs at that, then yes you are banded.

I believe it is possible to telnet into that from a Windows Command Prompt, but I'm not sure of the command for stats once you are in.

It may be xdslctl info --stats but I'm guessing from a Draytek 130 I had. With luck someone who can confirm or correct that will be along soon.

GUIs can often get things mixed up, but telnet I have never heard of being wrong.

here is the readout from telnet

> vdsl status

---------------------- ATU-R Info (hw: annex A, f/w: annex A/B/C) -----------
Running Mode : 17A State : SHOWTIME
DS Actual Rate : 48999000 bps US Actual Rate : 7323000 bps
DS Attainable Rate : 60786628 bps US Attainable Rate : 7323000 bps
DS Path Mode : Fast US Path Mode : Fast
DS Interleave Depth : 1 US Interleave Depth : 1
NE Current Attenuation : 23 dB Cur SNR Margin : 5 dB
DS actual PSD : 5. 8 dB US actual PSD : 13. 3 dB
NE CRC Count : 231 FE CRC Count : 24525
NE ES Count : 57 FE ES Count : 23040
Xdsl Reset Times : 0 Xdsl Link Times : 1
ITU Version[0] : b5004946 ITU Version[1] : 544e0000
VDSL Firmware Version : 05-07-06-0D-01-07 [with Vectoring support]
Power Management Mode : DSL_G997_PMS_L0
Test Mode : DISABLE
-------------------------------- ATU-C Info ---------------------------------
Far Current Attenuation : 34 dB Far SNR Margin : 6 dB
CO ITU Version[0] : b5004244 CO ITU Version[1] : 434da48c
DSLAM CHIPSET VENDOR : < BDCM >
> vdsl

% Valid subcommands are:
status idle drivermode reboot annex showbins
optn savecfg vendorid snr inventory
> vdsl status more

---------------------- ATU-R Info (hw: annex A, f/w: annex A/B/C) -----------
Near End Far End Note
Trellis : 1 1
Bitswap : 1 1
ReTxEnable : 0 1
VirtualNoise : 0 0
20BitSupport : 0 0
LatencyPath : 0 0
LOS : 0 0
LOF : 0 0
LPR : 0 0
LOM : 0 0
SosSuccess : 0 0
NCD : 0 0
LCD : 0 0
FECS : 0 4203 (seconds)
ES : 57 23040 (seconds)
SES : 10 0 (seconds)
LOSS : 0 0 (seconds)
UAS : 29 3100 (seconds)
HECError : 0 0
CRC : 231 24525
INP : 0 215 (symbols)
INTLVDelay : 0 13 (1/100 ms)
NFEC : 240 32
RFEC : 16 16
LSYMB : 1977 16
INTLVBLOCK : 120 32
AELEM : 0 ----
>