Technical Discussion
  >> Technical Issues


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
  Print Thread
Standard User dizzle21
(newbie) Sat 09-May-09 15:54:36
Print Post

New External NTE and old Master Socket


[link to this post]
 
A few weeks ago there was a fault with the telephone line and an Openreach engineer visited my property and deemed it necessary to replace the external line. He also installed a new External NTE claiming it would probably improve things and make it easier for subsequent engineer visits.

My question is I have still been left with the original BT master socket, and presuming the external NTE has the same components as a NTE5 master, could this increase the capacitance on the line and degrade broadband performance?

I have installed extension telephone sockets before so I would have no problem in replacing the master with an extension if needed. I'm not sure what the regulations are but since they have installed a new NTE outside, is the old master socket now my property? And should I replace it with an extension?

Shedding some light on this matter would be much appreaciated.
Standard User Rockh
(eat-sleep-adslguide) Sat 09-May-09 16:06:15
Print Post

Re: New External NTE and old Master Socket


[re: dizzle21] [link to this post]
 
As BT have moved the demarcation point by fitting a new external NTE there should be no issue with you replacing the old master socket with a slave or you could just cut the components out of the old master.

Dave
Standard User dizzle21
(newbie) Sat 09-May-09 16:16:50
Print Post

Re: New External NTE and old Master Socket


[re: Rockh] [link to this post]
 
I thought as much! The engineer should have mentioned this to me or done something about it.


Register (or login) on our website and you will not see this ad.

Standard User deleted
(deleted) Sat 09-May-09 16:30:37
Print Post

Re: New External NTE and old Master Socket


[re: dizzle21] [link to this post]
 
Having two master sockets won't significantly degrade the line, especially (as I suspect) the ring wire is only connected to one of the masters.
Standard User dizzle21
(newbie) Sat 09-May-09 16:47:48
Print Post

Re: New External NTE and old Master Socket


[re: deleted] [link to this post]
 
I've already removed the ring wire of the internal master socket. I don't want to be cutting the components of the BT socket just incase it is needed later, so I need to look for a new one.

To be honest, I've only read somewhere that having two masters on one line can have impact on your line, but I don't know actually know what it affects? Shall I leave the master as it is, or shall I replace it with an extension? Performanc is my main concern. If I'm replacing, I'll probably need to extend the wires with crimps as they are now very short after Redcare had been playing about with it the past.

Edited by dizzle21 (Sat 09-May-09 16:50:14)

Standard User deleted
(deleted) Sat 09-May-09 17:21:55
Print Post

Re: New External NTE and old Master Socket


[re: dizzle21] [link to this post]
 
Well you could temporarily disconnect the old master socket, and see what difference it makes. There are only 3 components in a master socket not found on a slave - a spark-gap, a 470K "test" resistor, and the 2mF ring capacitor. I can't see any of those having any great effect on ADSL, but it would put your mind at rest to remove them, if only temporarily.
Standard User dizzle21
(newbie) Sat 09-May-09 17:51:16
Print Post

Re: New External NTE and old Master Socket


[re: deleted] [link to this post]
 
My extensions are being fed off the internal master, so if I disconnect none of the phones will work in my house. Thats got me thinking, should the extensions be fed off the external NTE instead?
Standard User deleted
(deleted) Sun 10-May-09 12:07:58
Print Post

Re: New External NTE and old Master Socket


[re: dizzle21] [link to this post]
 
Strictly speaking, yes. Although running them off the second master will work.
Standard User Zarjaz
(knowledge is power) Sun 10-May-09 19:26:46
Print Post

Re: New External NTE and old Master Socket


[re: dizzle21] [link to this post]
 
If I'm replacing, I'll probably need to extend the wires with crimps as they are now very short after Redcare had been playing about with it the past.

Now that does raise an interesting point. By the book, the Redcare block 92A should be fed from a direct connection to the rear screws on the back of an NTE5A..... how does this work with the new external NTE ? Questions will be asked. Watch this space.

Standard User dizzle21
(newbie) Sun 10-May-09 19:57:51
Print Post

Re: Redcare


[re: Zarjaz] [link to this post]
 
When my house was built we managed to get a telephone connection next to the alarm panel so the block is located there for neatness really - it must be fed off one of the extensions. However, the block was not installed until a few months after we moved in, during which time we had chirps on the line, and Redcare only had access to the master socket for testing - hence the short wires.

Actually, after 7 years, we still have to put up with the chirps. Having read on the redcare website, it seems to be labelled as 'polling over speech'. Any ideas how this can be sorted?
  Print Thread

Jump to