Technical Discussion
  >> Technical Issues


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
Pages in this thread: 1 | [2] | 3 | 4 | 5 | 6 | 7 | (show all)   Print Thread
Standard User deleted
(deleted) Tue 11-Aug-09 01:25:09
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Well BT eventually came round and the router the engineer used failed to connect anywhere in the house. He fitted a Master Socket and got a download speed of around 1500 kbps or so with all the wiring in the house disconnected.

Adding in the downstairs extension dropped the speed to 1408 kbps and adding in the upstairs extension instantly dropped the connection totally. The engineer gave me the choice of no broadband at all or no upstairs phones. Great service, comes in and leaves the situation worse than when he arrived (he even butchered the connectors on the inside of the Master Socket).

Have since run a new cable up the stairs for testing purposes and got the phones back and 1408 kbps. Woo! Until I plugged in a short extension to the next room where the router normally lives. Instantly back to having no internet.

Replacing this extension with new cable got the internet running again but at 1280 kbps. No idea what was wrong with the wiring (both to get upstairs and also this extension) but the extension does run right past all the wiring for the house alarm and the main control box (with PSU I assume).

So much for the BT line checker we couldn't even get broadband where we live! We still have a forty year old piece of cable connecting us from the Master Socket to the BT line that comes to the house but as it runs down the outside wall and to the Master Socket I am guessing it belongs to BT and I should leave well enough alone.

Any idea how to shield the cable that runs past the alarm box and through all the incoming alarm wiring?

Thanks.
Standard User deleted
(deleted) Tue 11-Aug-09 07:56:45
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Sounds like you've got such a bad line that it will fall over, even in a strong wind !

Obviously I don't know your exact circumstances, but I think your only way to get telephones in other rooms is to use DECT phones, with the DECT base unit located at the master socket. If the alarm is kicking out that much interference, maybe you should consider replacing it ? I previously had an old wired alarm system myself, but I've recently replaced it with a much more up to date unit. The one I have now is totally wireless, and it even sends you a text when the alarm goes off, and you can activate and deactivate the alarm via text too. The phone connection is via a built-in PAYG mobile phone.

Take a look at www.global-gadgets.com

Edited by deleted (Tue 11-Aug-09 07:57:04)

Standard User ian72
(knowledge is power) Tue 11-Aug-09 08:28:33
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
What sort of wire are you using for the extensions (including the ones you've just replaced).

If it is standard telephone wire (or worse flat wire) then you may get a slightly better speed by using Cat5 network cable.


Register (or login) on our website and you will not see this ad.

Standard User deleted
(deleted) Tue 11-Aug-09 10:03:46
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Hi, from the NTE5 master socket, for the telephone extension points are you connecting to pin 2 and 5, or with pins 2-3-5 and using twisted pair telephone cable.

For modern telephones, you only need to use pin 2 and 5.

Further info http://forums.thinkbroadband.com/multiuser/t/3684312...
Standard User alwall
(regular) Tue 11-Aug-09 12:14:00
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
In reply to a post by asanyfuleno:
Well BT eventually came round and the router the engineer used failed to connect anywhere in the house. He fitted a Master Socket and got a download speed of around 1500 kbps or so with all the wiring in the house disconnected.[.....]
leaves the situation worse than when he arrived (he even butchered the connectors on the inside of the Master Socket).


1) You quoted your previous speed as 480 kbps so how is the situation worse at 1408 kbps?

2) How has your new Master Socket been butchered? A photo would be interesting.

3) I'm 99% certain that if the the router fails to connect on certain extensions that you have a fault with either your wiring, or connectors or the "short extension".
Dont use any plug in extension cables to carry an adsl signal if you arent using a filtered faceplate, they arent always twisted pair and could introduce interference.

4) Ideally I'd suggest plugging your router into a filtered faceplate on your new master socket such as http://www.adslnation.com/products/xte2005.php but you could always extend the unfiltered ADSL signal from terminals labelled B & A on the xte2005 using cat5e or 6 network cable with a network socket at the other end. I'm not convinced that screened cables will be worth the expenditure. Good quality twisted pair, either cw1308 or network cable should be fine.

BTBroadband
Standard User deleted
(deleted) Tue 11-Aug-09 17:56:13
Print Post

Re: Internal Telephone Wiring


[re: alwall] [link to this post]
 
1408 kbps is great but it is down to 1280 kbps now and I'd like to get it back up if I can. Have used four core telephone wire from Maplin. No idea if it is any good or not.

The master socket has the pins that cut in to the wire to make the connection pushed back in to the plastic housing so they don't hold the wire correctly without having the wire bent double to make it wide enough to grip.
Standard User deleted
(deleted) Tue 11-Aug-09 17:56:55
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Still using pins 2, 3 & 5 for the extensions as the last time I disconnected 3 everything stopped working.
Administrator MrSaffron
(staff) Tue 11-Aug-09 18:15:52
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
If disconnecting pin 3 stops you from making calls then the extensions are wired wrong.

Removing the ring wire makes no difference to phones, since they should have the ring signal regenerated by the microfilter the phone is plugged into.

Andrew Ferguson, [email protected]
www.thinkbroadband.com - formerly known as ADSLguide.org.uk
The author of the above post is a thinkbroadband staff member. It may not constitute an official statement on behalf of thinkbroadband.
Standard User alwall
(regular) Tue 11-Aug-09 18:23:09
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Pin 3 is the ring wire. It should not be needed. If removing it causes problems recheck your wiring.
Ditch it ASAP to improve your sync speed. The ADSL filters provide the ringing signal if needed.
Only use Blue/White on pin 2 in each socket and White/Blue on pin 5.
A new filtered faceplate as recommended will give you undamaged IDC terminals, just use the correct tool not a screwdriver.

Edit: Exactly Andrew!

BTBroadband

Edited by alwall (Tue 11-Aug-09 18:25:54)

Standard User deleted
(deleted) Tue 11-Aug-09 18:23:33
Print Post

Re: Internal Telephone Wiring


[re: deleted] [link to this post]
 
Weren't you going to post some pictures a month ago?
Pages in this thread: 1 | [2] | 3 | 4 | 5 | 6 | 7 | (show all)   Print Thread

Jump to