Technical Discussion
  >> Technical Issues


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
Pages in this thread: 1 | [2] | (show all)   Print Thread
Standard User Andrue
(knowledge is power) Mon 18-May-09 11:56:41
Print Post

Re: NTE5 socket odd behaviour


[re: deleted] [link to this post]
 
In reply to a post by panda:
It looks to me as if the NTE5A is installed in the wrong place.
If the hallway socket is the first point where the cable enters the building, this is where the NTE should be. The position where the NTE currently is, should be an extension socket.
Someone had an engineer install previously?

Cables enter my property in the front room but then leave again, fly across the front of the house and re-enter in the 'study' where the master now is. In my case I first had Home Highway installed then got an engineer to convert to ADSL so that they'd refund the cost if it turned out that ADSL didn't work on my line.

Andrue Cope
Brackley, UK

Just because he can smile
Standard User deleted
(deleted) Mon 18-May-09 21:43:34
Print Post

Re: NTE5 socket odd behaviour


[re: Rockh] [link to this post]
 
In reply to a post by Rockh:
As Panda has said it's either been installed in the wrong place or it has been moved. As you've tidied up the wiring and don't use any other phones then the extension socket is now a joint. There are no extra components in the extension socket so it shouldn't cause any issues unless someone plugs a phone in without a filter.

You could replace the slave socket with a joint box and fit a blanking plate over the dryline box. Technically this is BT's wiring as it's before the NTE5 and shouldn't be touched though.


I'll probably just leave the slave socket as it is, but I'm just wondering what components that little brown printed circuit board has on it, and if any of those components can add "noise" to the ADSL circuit.

Also I'm wondering if it's normal for the connection between the street and the NTE5 to be made using 6 core cable. The 6 core cable has 2xblue, 2xorange & 2xgreen wires yet only the blue wires are connected to the NTE5.

Edited by deleted (Mon 18-May-09 21:44:51)

Standard User Zarjaz
(knowledge is power) Mon 18-May-09 21:50:40
Print Post

Re: NTE5 socket odd behaviour


[re: deleted] [link to this post]
 
Also I'm wondering if it's normal for the connection between the street and the NTE5 to be made using 6 core cable. The 6 core cable has 2xblue, 2xorange & 2xgreen wires yet only the blue wires are connected to the NTE5.

Very usual indeed. I would wager that your line is fed from some internal DP within the flats, so the need for external grade cable is negated.

I think you are worrying unduly.


Register (or login) on our website and you will not see this ad.

Standard User Rockh
(eat-sleep-adslguide) Tue 19-May-09 09:25:30
Print Post

Re: NTE5 socket odd behaviour


[re: deleted] [link to this post]
 
There are no compoments on a slave.

Dave
Standard User deleted
(deleted) Tue 19-May-09 20:14:04
Print Post

Re: NTE5 socket odd behaviour


[re: Rockh] [link to this post]
 
In reply to a post by Rockh:
There are no compoments on a slave.


The brown printed circuit board of the slave socket shown in photo:
http://www.boliston.co.uk/temp/extension_tidied.jpg
shows what look like symbols for "resistors" or some sort of component between terminal #4 & terminal #5 and also something else between terminal #3 & terminal #2.

I notice that there are 3 retaining screws on the PCB so I might have a look to see if there are any components soldered to the rear of the board.

The main reason I'm concerned about noise at the moment is that BT have put me on a "banded profile" of about 30% of the speed that my line will support and the reason they put people on banded profiles is errors on the line caused by noise. I'm hoping that if I can reduce noise then BT will remove the banded profile.

I seem to be getting about 20 errors per hour at the moment but I'm not sure what counts as "a lot of errors"

(stats from my router since last reboot)

P-660HW-T> wan adsl perfdata
near-end FEC error fast: 20
near-end FEC error interleaved: 0
near-end CRC error fast: 27
near-end CRC error interleaved: 0
near-end HEC error fast: 24
near-end HEC error interleaved: 0
far-end FEC error fast: 0
far-end FEC error interleaved: 0
far-end CRC error fast: 65504
far-end CRC error interleaved: 0
far-end HEC error fast: 0
far-end HEC error interleaved: 0
ADSL uptime 1:11:08

P-660HW-T> wan adsl chandata
DSL standard: ADSL2 DELT
near-end interleaved channel bit rate: 0 kbps
near-end fast channel bit rate: 4544 kbps
far-end interleaved channel bit rate: 0 kbps
far-end fast channel bit rate: 1080 kbps

P-660HW-T> wan adsl linedata near
noise margin downstream: 19 db
output power upstream: 11 db
attenuation downstream: 30 db

P-660HW-T> wan adsl linedata far
noise margin upstream: 6 db
output power downstream: 0 db
attenuation upstream: 17 db
Standard User deleted
(deleted) Tue 19-May-09 20:32:52
Print Post

Re: NTE5 socket odd behaviour


[re: deleted] [link to this post]
 
You will likely find nothing solderted to the PCB, the manufacturer likely uses the same PCB's for master type and secondary type sockets, and just leaves out the components on secondary type sockets as shown.
Pages in this thread: 1 | [2] | (show all)   Print Thread

Jump to