General Discussion
  >> Fibre Broadband


Register (or login) on our website and you will not see this ad.


Pages in this thread: 1 | 2 | [3] | (show all)   Print Thread
Standard User deleted
(deleted) Fri 25-Mar-11 13:48:54
Print Post

Re: Today's the Day For The FTTC Installation


[re: RobertoS] [link to this post]
 
Well I've just had my infinity installed. No idea about my sync speed as the openreach engineer didn't bring his line test device and just wanted to use speedtest.net. So I have no idea as to my line length frown

My ADSL Nation faceplate was left in place after we agreed to "see if it worked" and my HH3.0 is working correctly.

http://www.speedtest.net/result/1219714302.png
http://www.pingtest.net/result/37580895.png

BT Speedtester doesn't work yet as I guess my activation is too new so I'll give it a few hours and see if it works.

I've attempted to use my 7800N EWAN router - which is configured to use PPPoE on the EWAN port but it doesn't wish to connect. Tried with both the generic bthomehub@ and using my new @btinternet email address.

System log reports the following -

Jan 01 00:43:50 daemon pppd[468]: PPP: Start to connect ...
Jan 01 00:44:13 daemon pppd[468]: Couldn't get channel number: Transport endpoint is not connected
Jan 01 00:44:13 daemon pppd[468]: PPP: PPP Server No Response !!!
Jan 01 00:44:13 daemon pppd[468]: Doing disconnect

Any ideas chaps? smile
Standard User deleted
(deleted) Fri 25-Mar-11 14:36:41
Print Post

Re: Today's the Day For The FTTC Installation


[re: deleted] [link to this post]
 
Well after some tweaking, and reboot of the router a few times. It's now successfully established a connection and I no longer need to use the HH smile

Using my 7800N -
http://www.pingtest.net/result/37583791.png
http://www.speedtest.net/result/1219804345.png

Edited by deleted (Fri 25-Mar-11 14:37:17)

Anonymous
(Unregistered)Fri 25-Mar-11 14:41:25
Print Post

Re: Today's the Day For The FTTC Installation


[re: deleted] [link to this post]
 
In reply to a post by meditator:
My understanding is that the ADSL Nation faceplate with both a filtered output for telephone equipment and an unfiltered output for ADSL has been approved by BT.

As there is no official document to support your understanding, I believe it's a misunderstanding
I wonder how much change you'd have left out of £200 if you reported and VDSL sync issue and the attending engineer found a non-standard faceplate to be the cause of the problem.


Register (or login) on our website and you will not see this ad.

Anonymous
(Unregistered)Fri 25-Mar-11 15:08:28
Print Post

Re: Today's the Day For The FTTC Installation


[re: Anonymous] [link to this post]
 
indeed, I would have the engineer fit all the standard fittings, if you want to run the nation plate (why though?) then change it around afterwards - at least you get a spare filter plate out of it and can avoid a bill of the nation plate ever went faulty.
Standard User RobertoS
(sensei) Fri 25-Mar-11 16:17:20
Print Post

Re: Today's the Day For The FTTC Installation


[re: deleted] [link to this post]
 
Pretty good smile.

My broadband basic info/help site - www.robertos.me.uk
My domains,website and mail hosting - Tsohost. Internet connection - IDNet Home Starter Fibre. Live BQM.
Standard User mrnelster
(member) Sat 26-Mar-11 09:09:00
Print Post

Re: Today's the Day For The FTTC Installation


[re: RobertoS] [link to this post]
 
What about that ping? Many posters seem to have a 6-12 ms ping when they connect at the higher speeds.

My 5km line can achieve 42ms on a good day. How do you estimate what you should expect relative to the reduced cooper line length or is it just an ISP's chosen settings that dictate?

Thanks.

Knowing how it works is completely different to understanding how it works.
Standard User RobertoS
(sensei) Sat 26-Mar-11 09:14:33
Print Post

Re: Today's the Day For The FTTC Installation


[re: mrnelster] [link to this post]
 
Copper length isn't really relevant apart from possible noise introduction. More to do with the same factors as before I think - ISP capacity and routing.

I haven't seen many under the 11-12ms I average though.

My broadband basic info/help site - www.robertos.me.uk
My domains,website and mail hosting - Tsohost. Internet connection - IDNet Home Starter Fibre. Live BQM.
Standard User mrnelster
(member) Sat 26-Mar-11 09:24:15
Print Post

Re: Today's the Day For The FTTC Installation


[re: RobertoS] [link to this post]
 
Thanks for your reply. Thats good to know. smile

So when I order FTTC I suppose I could ask my chosen ISP for an indication of what my line may be able to achieve? I'm only around 300m from my cab so I'm expecting a high profile and sync.

Famous last words perhaps!

Knowing how it works is completely different to understanding how it works.
Standard User RobertoS
(sensei) Sat 26-Mar-11 09:39:53
Print Post

Re: Today's the Day For The FTTC Installation


[re: mrnelster] [link to this post]
 
In reply to a post by mrnelster:
Thanks for your reply. Thats good to know. smile

So when I order FTTC I suppose I could ask my chosen ISP for an indication of what my line may be able to achieve? I'm only around 300m from my cab so I'm expecting a high profile and sync.

Famous last words perhaps!
300m from cabinet copper run should get 40000 connection and whatever upload you order. Anything up to 500m or so seems to. I walked mine months ago and got around 500m, since when the FTTC cab has been sited about 30m from it, and the engineer test showed (approx) 0.6km, 39992/10000.

IP Profile is the maximum 38717.

Re latency, best to say (in a new thread of your own tongue) which ISP you are considering and see what existing users have to say.

My broadband basic info/help site - www.robertos.me.uk
My domains,website and mail hosting - Tsohost. Internet connection - IDNet Home Starter Fibre. Live BQM.
Pages in this thread: 1 | 2 | [3] | (show all)   Print Thread

Jump to