Just looking at my HG612 output, I have

bitswap         On
sra             Off
trellis         On
sesdrop         Off
CoMinMgn        Off
24k             On
phyReXmt(Us/Ds) Off/On
TpsTc           AvPvAa
monitorTone:    On
dynamicD:       On
dynamicF:       Off
SOS:            On

What I can't see is where phyReXmt(Us/Ds) is set . It should be possible.

Edited by RobertoS (Wed 27-Jan-16 13:47:01)

In reply to a post by RobertoS:

Just looking at my HG612 output, I have

bitswap         On
sra             Off
trellis         On
sesdrop         Off
CoMinMgn        Off
24k             On

phyReXmt(Us/Ds) Off/On

TpsTc           AvPvAa
monitorTone:    On
dynamicD:       On
dynamicF:       Off
SOS:            On

What I can't see is where phyReXmt(Us/Ds) is set . It should be possible.

Sorry? Oh, do you mean in the config?

Edited by deleted (Wed 27-Jan-16 13:51:03)

Yes . We can see there what it is set at, and it is present in the config, but not with on/off or other parameters so far as I can tell.

This any good? http://www.dslreports.com/forum/r28768737-

Interesting!

It works, though I did use xdslcmd rather than adsl

No appreciable difference.

I inadvertently did a start earlier, changing from what is in my sig in this post, (and correct earlier today and for weeks), to

Max: 15540/58416
Bearer 0: 15589/59465

to

Max: 15641/58888
Bearer 0: 15641/59504

Bearer 1: No change.

Of course, the thread you linked to was October 2013. Anyone know if upstream G.INP was active then?

What we do know now though is that if and when upstream G.INP is re-implemented, then unless it is forced from the DSLAM by a remote command that this firmware probably won't pick it up automatically.

Anyone got any historic stats showing upstream G.INP?

xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 31924 Kbps, Downstream rate = 85088 Kbps
Bearer: 0, Upstream rate = 20000 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 7.1 13.7
Attn(dB): 13.5 0.0
Pwr(dBm): 12.4 3.2
VDSL2 framing
Bearer 0
MSGc: -6 -6
B: 130 97
M: 1 1
T: 0 0
R: 8 8
S: 0.0518 0.1554
L: 21468 5457
D: 16 8
I: 139 106
N: 139 106
Q: 16 8
V: 14 2
RxQueue: 57 39
TxQueue: 19 13
G.INP Framing: 18 18
G.INP lookback: 19 13
RRC bits: 24 24
Bearer 1
MSGc: 186 58
B: 0 0
M: 2 2
T: 2 2
R: 16 16
S: 5.3333 16.0000
L: 48 16
D: 3 1
I: 32 32
N: 32 32
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 0
OHFErr: 0 0
RS: 3142915696 6650
RSCorr: 41460 7558
RSUnCorr: 0 0
Bearer 1
OHF: 19924295 79372
OHFErr: 0 0
RS: 239090802 2699853
RSCorr: 0 100
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 1647 727
rtx_c: 1435 714
rtx_uc: 0 0

G.INP Counters
LEFTRS: 15 7
minEFTR: 79999 19991
errFreeBits: 390491898 97609585

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 1990925181 0
Data Cells: 900636194 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 11 1
SES: 10 0
UAS: 69 59
AS: 320038

Bearer 0
INP: 46.00 47.00
INPRein: 0.00 0.00
delay: 0 0
PER: 0.00 0.00
OR: 0.01 0.01
AgR: 80614.82 20102.08

Bearer 1
INP: 4.00 4.00
INPRein: 4.00 4.00
delay: 3 0
PER: 16.06 16.06
OR: 95.62 31.87
AgR: 95.62 31.87

Bitswap: 130964/130964 276/276

From last March When G.inp was enabled on the upstream, And now it isn't, The G.inp is controlled from the DSLAM if the modem supports it , it should use it ,

once the DSLAM can see that a device doesn't support G.inp it uses a fall back profile which is interleave on both upstream and downstream for a short time, I know i have tested by using the incompatible ECI modem , It started off with normal fastpath latency and Full sync rates ,confirmed by the Max BTIP profile,

Then after iirc 2 weeks DLM borked the connection, leaving the ECI is a strange unresponsive state, with no internet access ( this was /is a ECI modem that as far as i know didn't get g.inp enabled update,because it wasn't in use) I connected the HG612 and could see it was interleaved both up and down, after 2 days or less dlm re configured things to only downstream interleave , then again within 24hrs reduced the depth, 2 days later g.inp was back on the ds everything as it was before

V100R001C01B030SP06

Thanks Tommy . Now I know what they are likely to look like.

Re your SP06 at the end, my SP08 was copy and pasted straight off my HG612 GUI immediately before posting. That raises an interesting point if you are still using it, as to what xdslcmd profile --show says.

Software version = V100R001C01B030SP06
Software last change detected at 03/11/2015 at 00:33

Firmware version = A2pv6C038m.d24j
Firmware last change detected at 03/11/2015 at 00:33

CPU version = BCM6368
CPU last change detected at 03/11/2015 at 00:33

CFE version = 1.0.37-102.6
CFE last change detected at 03/11/2015 at 00:33

From Modem stats as it won't allow another telnet login

In reply to a post by tommy45:

V100R001C01B030SP06

Oh, so that support G.INP as well. That's no good then to disable G.INP we need B028SP06 or 10 ?

Yes i have used the same F/W all the time that I've been using the hg612 , i never bothered updating at the time because iirc there wasn't a unlocked version without bt agent that had the gui access ,but as i found out this version works with G.inp anyway

I would imagine the version that was released before this version or any of the older versions will not work with G.inp