The HH5A doesn't support G.INP.

Is there any criteria for G.INP to be enabled? i.e DLM, FEC error count etc.

In reply to a post by BatBoy:

That's probably due to interleaving being removed

Could you explain what you mean? You've lost me there a bit. Interleaving wasn't enabled, it was a fresh port as far as I can remember. Just relaying what I was told that the max attainable speed was lower due to "retransmission being enabled".

Removing interleaving increases the sync speed, that's why I'm confused by your comment.

Mine went G.INP this morning just after 8am.

I'm not really sure if it affected attainable rates as I've always been pegged at max sync, and the situation is more murky due to it being a brand new cab installed last week after a car crashed into the old one.

BTOR have been working on it every day causing drops and all sorts of other issues. My attainables have been jumping all over the place, from 95-115mbit. Right now seems settled at 101mbit.

Only thing I can see for sure has changed due to G.INP coming on is my latency has gone up by ~3ms. Back in my online gaming days I'd be furious about such a huge (!) increase in latency.. but now.. meh.

Interleaving has a side effect of increasing max attainable. Obviously, if there's no interleaving applied it's not that. Maybe retransmission does decrease the max attainable, but the max attainable is mostly irrelevant anyway.

24 hours ago my VDSL connection dropped. It was 68/16, now it's 73/16:

---------------------- ATU-R Info (hw: annex A, f/w: annex A/B/C) -----------
Running Mode : 17A State : SHOWTIME
DS Actual Rate : 73350000 bps US Actual Rate : 16613000 bps
DS Attainable Rate : 73590208 bps US Attainable Rate : 16722588 bps
DS Path Mode : Fast US Path Mode : Fast
DS Interleave Depth : 1 US Interleave Depth : 1
NE Current Attenuation : 19 dB Cur SNR Margin : 5 dB
DS actual PSD : 6. 7 dB US actual PSD : 13. 9 dB
NE CRC Count : 20 FE CRC Count : 2909
NE ES Count : 14 FE ES Count : 2711
Xdsl Reset Times : 0 Xdsl Link Times : 2
ITU Version[0] : b5004946 ITU Version[1] : 544e0000
VDSL Firmware Version : 05-07-06-0D-01-07 [with Vectoring support]
Power Management Mode : DSL_G997_PMS_L0
Test Mode : DISABLE
-------------------------------- ATU-C Info ---------------------------------
Far Current Attenuation : 24 dB Far SNR Margin : 6 dB
CO ITU Version[0] : b5004946 CO ITU Version[1] : 544eb204
DSLAM CHIPSET VENDOR : < IFTN >
> vdsl status more

Near End Far End Note
Trellis : 1 1
Bitswap : 0 1
ReTxEnable : 0 1

Which modem/router model are you using Reado?

What does it mean when interleave is set at 1? my line was recently fixed and dlm reset was done and my interleave is 1, with speeds higher than they have ever been

Edited by zebo (Tue 22-Mar-16 10:22:14)

So if I have read this correctly all cabinets will pretty much get g.inp but it's up to DLM if it's activated on your line?

In reply to a post by underzone:

Which modem/router model are you using Reado?

I'm using the DrayTek 2860ac with the latest firmware (3.8.2.2_VT3) which supports Vectoring and G.INP.