General Discussion
  >> Fibre Broadband


Register (or login) on our website and you will not see this ad.


Pages in this thread: 1 | [2] | (show all)   Print Thread
Standard User deleted
(deleted) Sat 26-Mar-16 07:32:36
Print Post

Re: Upgrading HG612 firmware issue


[re: deleted] [link to this post]
 
I think G.INP has just about 20 minutes or so ago just been applied to my line despite reading somewhere the chipset for the ECI cab must be xb206 for eci when G.INP enabled when using the vendor command on the HG612? The stats on the webgui have gone a bit weird and are all over the place. However my latency like expected is now 10ms. The bearer is now 1 on the stats however i hardly gained anything in sync speed it was previously 22399 now its 22400.

Do the stats look ok for G.INP?

# xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 5519 Kbps, Downstream rate = 29904 Kbps
Bearer: 0, Upstream rate = 2000 Kbps, Downstream rate = 22400 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 9.9 13.1
Attn(dB): 24.3 0.0
Pwr(dBm): 11.6 5.4
VDSL2 framing
Bearer 0
MSGc: -6 330
B: 174 48
M: 1 1
T: 0 6
R: 12 16
S: 0.2486 0.7651
L: 6018 711
D: 1 1
I: 187 68
N: 187 68
Q: 16 0
V: 3 0
RxQueue: 12 0
TxQueue: 6 0
G.INP Framing: 18 0
G.INP lookback: 6 0
RRC bits: 0 24
Bearer 1
MSGc: 90 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 10.6667 0.0000
L: 24 0
D: 1 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 89703
OHFErr: 0 0
RS: 23096768 3238263
RSCorr: 2905 0
RSUnCorr: 0 0
Bearer 1
OHF: 89774 0
OHFErr: 0 0
RS: 538273 0
RSCorr: 0 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 24 0
rtx_c: 18 0
rtx_uc: 0 0

G.INP Counters
LEFTRS: 0 0
minEFTR: 22380 0
errFreeBits: 491718 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 62071756 0
Data Cells: 2148323 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 38 2
SES: 10 0
UAS: 94 84
AS: 1443

Bearer 0
INP: 43.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 0.00 16.13
OR: 0.01 166.64
AgR: 22439.61 2166.36

Bearer 1
INP: 2.50 0.00
INPRein: 2.50 0.00
delay: 0 0
PER: 16.06 0.01
OR: 47.81 0.01
AgR: 47.81 0.01

Bitswap: 1217/1217 0/0

Total time = 21 hours 36 min 7 sec
FEC: 14575426 20
CRC: 2254 2
ES: 38 2
SES: 10 0
UAS: 94 84
LOS: 1 0
LOF: 8 0
LOM: 0 0
Latest 15 minutes time = 6 min 7 sec
FEC: 439 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 2421 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 21 hours 36 min 7 sec
FEC: 14575426 20
CRC: 2254 2
ES: 38 2
SES: 10 0
UAS: 94 84
LOS: 1 0
LOF: 8 0
LOM: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 24 min 1 sec
FEC: 2905 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
#

Thanks
Standard User deleted
(deleted) Sat 26-Mar-16 10:38:18
Print Post

Re: Upgrading HG612 firmware issue


[re: deleted] [link to this post]
 
In reply to a post by Computerman142:
I think G.INP has just about 20 minutes or so ago just been applied to my line despite reading somewhere the chipset for the ECI cab must be xb206
Dunno where you read that but it's wrong.

G.INP is active on your connection and looks fine.
Pages in this thread: 1 | [2] | (show all)   Print Thread

Jump to