General Discussion
  >> Fibre Broadband


Register (or login) on our website and you will not see this ad.


Pages in this thread: 1 | 2 | 3 | 4 | 5 | [6] | (show all)   Print Thread
Standard User Whitehall11
(member) Tue 11-May-21 00:13:08
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: jabuzzard] [link to this post]
 
In reply to a post by jabuzzard:
In reply to a post by RR_The_IT_Guy:
I know a local company that are quite cheap and do major installs very well and the companies that use them have reused them whenever they expanded the fibre network so its clearly good as the links work.


Right fibre is going to be hugely expensive compared to copper. I would suggest at least £100 to splice LC connectors on each end of a run. Further unless you do it in single mode the fibre will not stand the test of time, and single mode optics are even more expensive than multimode.

Fibre in a domestic property is almost always about as sensible as Cat7/8 cable. It is only really justified in reaching an outbuilding that would put you over the distance limit. Just install some Cat6a and be done with it.


Yeah i think you get to about the 100m mark and the cost / benefit of CAT6 is outweiged by Fibre. Got a spool of the fibre stuff for £50
Standard User Pheasant
(fountain of knowledge) Tue 11-May-21 03:33:34
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: Whitehall11] [link to this post]
 
In reply to a post by Whitehall11:
In reply to a post by jabuzzard:
In reply to a post by RR_The_IT_Guy:
I know a local company that are quite cheap and do major installs very well and the companies that use them have reused them whenever they expanded the fibre network so its clearly good as the links work.


Right fibre is going to be hugely expensive compared to copper. I would suggest at least £100 to splice LC connectors on each end of a run. Further unless you do it in single mode the fibre will not stand the test of time, and single mode optics are even more expensive than multimode.

Fibre in a domestic property is almost always about as sensible as Cat7/8 cable. It is only really justified in reaching an outbuilding that would put you over the distance limit. Just install some Cat6a and be done with it.


Yeah i think you get to about the 100m mark and the cost / benefit of CAT6 is outweiged by Fibre. Got a spool of the fibre stuff for £50

That's 100m roll of pre-terminated (with FC conn's) light armoured singlemode is it not? 😎 Add a pair of gigabit BiDi actives for £25 and a FC/LC patch leads or two for a fiver. Bob's your fathers brother.😂
Standard User candlerb
(fountain of knowledge) Tue 11-May-21 11:28:46
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: jabuzzard] [link to this post]
 
In reply to a post by jabuzzard:
and single mode optics are even more expensive than multimode.


At 1G and 10G the optics price is insignificant: about £7 each end for 1G (1000baseLX), and £21 for 10GbaseLR (10G) - from fs.com

I'd say getting pre-terminated duplex fibres is the way to go. I'd certainly recommend this in a domestic situation when you're running connections between buildings. Lightning can induce substantial potential differences.


Register (or login) on our website and you will not see this ad.

Standard User ft247
(member) Tue 11-May-21 12:00:27
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: candlerb] [link to this post]
 
Internal fibre in a domestic situation really comes down to what's on the end of the links. Preterminated fibre is not a massive cost relative to Cat6 - if indoors and in conduit standard yellow patch cable is fine.

If you're using kit that has SFP cages, then fibre is a very accessible option.

If you have an ISP/domestic router, switch etc. and nothing but a bunch of access points and devices with copper ports, then it's not worth getting all the media converters etc. required to make use of it.

If you're on the fence and are rewiring, then a few runs of duplex single-mode fibre are worth throwing in the walls at the same time as the copper for minimal cost.

If you're digging to an outbuilding, then fibre has electrical isolation benefits and you'd likely need to buy a new switch for the outbuilding, so may as well get something with an SFP cage. In that case a single media converter for the house end makes sense if needed.
Standard User Pheasant
(fountain of knowledge) Tue 11-May-21 17:31:24
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: candlerb] [link to this post]
 
In reply to a post by candlerb:
In reply to a post by jabuzzard:
and single mode optics are even more expensive than multimode.


At 1G and 10G the optics price is insignificant: about £7 each end for 1G (1000baseLX), and £21 for 10GbaseLR (10G) - from fs.com

I'd say getting pre-terminated duplex fibres is the way to go. I'd certainly recommend this in a domestic situation when you're running connections between buildings. Lightning can induce substantial potential differences.

(as you're no doubt aware) at a pinch you could run single core fibre for a point-to-point link giving up to 10Gb/s on inexpensive single-mode BiDi optics. Works out about £30 per end for 10km and 20km optics (...way more then enough unless you're on a royal estate in the Highlands!).

Beyond those bandwidths for the time being its back to go old duplex fibre for seperate transmit and receive pathways for the link. Always good to slightly over-provision "wires" any way. You never know when you might need to run 400Gbs from AWS or Google to your bedroom data centre
Standard User Whitehall11
(member) Tue 11-May-21 17:43:08
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: Pheasant] [link to this post]
 
In reply to a post by Pheasant:
In reply to a post by Whitehall11:
In reply to a post by jabuzzard:
... nested quotes trimmed ...


Right fibre is going to be hugely expensive compared to copper. I would suggest at least £100 to splice LC connectors on each end of a run. Further unless you do it in single mode the fibre will not stand the test of time, and single mode optics are even more expensive than multimode.

Fibre in a domestic property is almost always about as sensible as Cat7/8 cable. It is only really justified in reaching an outbuilding that would put you over the distance limit. Just install some Cat6a and be done with it.


Yeah i think you get to about the 100m mark and the cost / benefit of CAT6 is outweiged by Fibre. Got a spool of the fibre stuff for £50

That's 100m roll of pre-terminated (with FC conn's) light armoured singlemode is it not? 😎 Add a pair of gigabit BiDi actives for £25 and a FC/LC patch leads or two for a fiver. Bob's your fathers brother.😂


Lol you'll hopefully see the results of this by the end of the week!
Standard User Pheasant
(fountain of knowledge) Tue 11-May-21 17:46:38
Print Post

Re: Openreach Full Fibre Install - Modem/Router locations


[re: Whitehall11] [link to this post]
 
In reply to a post by Whitehall11:
In reply to a post by Pheasant:
In reply to a post by Whitehall11:
... nested quotes trimmed ...


Yeah i think you get to about the 100m mark and the cost / benefit of CAT6 is outweiged by Fibre. Got a spool of the fibre stuff for £50

That's 100m roll of pre-terminated (with FC conn's) light armoured singlemode is it not? 😎 Add a pair of gigabit BiDi actives for £25 and a FC/LC patch leads or two for a fiver. Bob's your fathers brother.😂


Lol you'll hopefully see the results of this by the end of the week!

Check your PMs...😎
Pages in this thread: 1 | 2 | 3 | 4 | 5 | [6] | (show all)   Print Thread

Jump to