Disconnect the pin 3 wire from all sockets it is connected at

As this is internal wiring, it will cost about £200 if you call BT OR out to fix it

In reply to a post by ZMeshign:

Previous times the login wouldn't work but it somehow did this time after I tried again with his her instructions.

Does my link http://192.168.1.1/setup.cgi?PATH=/bin:/sbin:/usr/bi... now work? it should!

Okay I have disconnected pin #3 bell wires from 2 sockets that had it, now as the link you provided still doesn't work, I have got info from telnet again and here it is:
"adslctl: ADSL driver and PHY status
Status: ShowtimeRetrain Reason: 8000
Channel: FAST, Upstream rate = 775 Kbps, Downstream rate = 2087 Kbps
Link Power State: L0
Mode: ADSL2
Channel: Fast
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 6.3 6.1
Attn(dB): 53.5 31.8
Pwr(dBm): 0.0 12.7
Max(Kbps): 3152 776
Rate (Kbps): 2087 775
G.dmt framing
K: 66(0) 24
R: 0 0
S: 1 1
D: 1 1
ADSL2 framing
MSGc: 59 12
B: 65 23
M: 1 1
T: 1 4
R: 0 0
S: 0.9962 0.9795
L: 530 196
D: 1 1
Counters
SF: 6567 6195
SFErr: 32 0
RS: 0 0
RSCorr: 0 0
RSUnCorr: 0 0

HEC: 5 0
OCD: 0 0
LCD: 0 0
Total Cells: 523963 190924
Data Cells: 92780 39439
Drop Cells: 0
Bit Errors: 0 0

ES: 24 0
SES: 0 740
UAS: 38 0
AS: 106

INP: 0.00 0.00
PER: 16.18 17.63
delay: 0.24 0.24
OR: 32.12 8.16

Bitswap: 18 0

Total time = 49710 days 6 hours 25 min 59 sec
SF = 6567
CRC = 32
LOS = 0
LOF = 0
ES = 24
Latest 1 day time = 49710 days 6 hours 25 min 59 sec
SF = 6567
CRC = 32
LOS = 0
LOF = 0
ES = 24
Latest 15 minutes time = 49710 days 6 hours 25 min 59 sec
SF = 6567
CRC = 32
LOS = 0
LOF = 0
ES = 24
Previous 15 minutes time = 0 sec
SF = 0
CRC = 0
LOS = 0
LOF = 0
ES = 0
Previous 1 day time = 0 sec
SF = 0
CRC = 0
LOS = 0
LOF = 0
ES = 0
Showtime Drop Reason: 8000
Last Retrain Reason: 8000"

What should I do next? (By the way, my speed is still 1.7mbps as speedtest.net shows)

Edited by deleted (Wed 14-Sep-11 18:44:11)

Oh well, I give up! At least my nagging you to get the full stats has confirmed you are getting loads of errors on your connection

Hasn't my connection improved?

I thought it did after doing this because my CRC is so lower than before now....

It seems that my CRC has decreased but still my connection speed has not improved.

Are there any other things I should do?

Yes, but they are still bad
Before: CRC/SF = 8% is very high; AS/ES = 1 sec between each ES is awful
Now: CRC/SF = 0.49% is still high; AS/ES = 4 sec between each ES is still too high.

But it has only been running for a couple of mins. So let it run longer, at least 4 hours, and see how it goes.

Edited by XRaySpeX (Wed 14-Sep-11 20:23:08)

Does that mean I can't fix it?

Do you have any suggestions about what I should do to fix all my problems and get a stable & speedy connection?

Dunno, but from the rest of this thread it seems likely that it is your wiring that is the issue as I pointed out before.