User comments on ISPs
  >> PlusNet plc


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
  Print Thread
Standard User sallymoo
(newbie) Thu 12-Oct-06 23:16:18
Print Post

Maxdsl speeds during first ten days?


[link to this post]
 
Hi, I paid my
Standard User ScaryMonkey
(fountain of knowledge) Thu 12-Oct-06 23:46:47
Print Post

Re: Maxdsl speeds during first ten days?


[re: sallymoo] [link to this post]
 
What speed does the BT speedtester say your line is set to? (http://speedtester.bt.com) THe tester can be run from your Plusnet connection in this instance as you are looking for the profile setting BT currently have you on (although they may not as you are still within the 10 days).
Basically in the first 10 days you could get any speed, and you should really only reboot the router once a day if possible. 10 times a day is risking the BT kit knobbling your connection as it thinks your line isn't capable of handling the conneciton at the SNR you have. It then increases yout SNR and starts slowing your connection.

Vince

Back on Force9......I get what I expect here.

14 year olds racing cars - see our teams progress at MVRacing.co.uk
Standard User UKSMS
(fountain of knowledge) Thu 12-Oct-06 23:47:15
Print Post

Re: Maxdsl speeds during first ten days?


[re: sallymoo] [link to this post]
 
Whats your sync speed?

Speeds are quite often stuck at 2 meg even if your syncing at 2-8meg speeds from anything up to 14 days but normally they kick in after a few days.



Pluscali No Need to Monitor your usage *

*Applies only to the first 2GB


Register (or login) on our website and you will not see this ad.

Standard User soundsystem
(fountain of knowledge) Fri 13-Oct-06 00:28:39
Print Post

Re: Maxdsl speeds during first ten days?


[re: sallymoo] [link to this post]
 
sallymoo

I f you have been maxed, I would not worry about anything until at least 10 days have passed, try not to keep turning your router on and off, the best speed possible will be attained during this period.

Happy to be on freedom2surf - 4MB 50gb Cap on GW2

All you need to know about Sky Broadband - visit the unofficial forums

Plusnet Support: 0845 1400200 pass it on! Plusnetters Community

Just a tad happy..a wee bit young
Standard User sallymoo
(newbie) Fri 13-Oct-06 08:39:54
Print Post

Re: Maxdsl speeds during first ten days?


[re: soundsystem] [link to this post]
 
ScaryMonkey - I've tried http://speedtester.bt.com a dozen times before and it never works for me. It either gives me a TAP1 error or just sits there doing nothing, after the blue progress bar moves about one-thrid across. I note that page says "if you are operating a Virtual Private Networking (VPN) you will not be able to use the Performance Tester for throughput testing due to the Address Proxy function, which is almost " - I use a 4 port router connected to another couple of computers in the house - perhaps this would be classed as a VPN?

UKSMS - Is sync speed the same as 'ADSL Status'? If so, my router says "Up Speed 448000, Down Speed 8128000" Does this help?

Thanks.
Standard User keithmdw
(newbie) Fri 20-Oct-06 07:35:23
Print Post

Re: Maxdsl speeds during first ten days?


[re: ScaryMonkey] [link to this post]
 
So if I were to switch my router off in the morning before going to work, and back on when I get in from work, but leave it on the rest of the time, would this cause me problems?

I switched off overnight, then on this morning, and then back off before leaving for work, as I thought that was a good idea.

I was upgraded yesterday.

Certainly don't want any undue problems, so should I start leavign it on 24/7 as usual?


EDIT: Just noticed the following on the PlusNet website actually advising you switch the kit off:

Tests are carried out during this period to see what speed your line can support. It's important that you frequently make new connections to the Internet during this 10 day period so these tests can take place.

It

Edited by keithmdw (Fri 20-Oct-06 07:49:16)

  Print Thread

Jump to