Technical Discussion
  >> Technical Issues


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
Pages in this thread: 1 | 2 | (show all)   Print Thread
Standard User silvryn
(learned) Wed 25-Mar-09 21:13:11
Print Post

Wiring an RJ11 cable for dsl modem?


[link to this post]
 
Hi all,
I was wondering whcih RJ11 jack would be best to use to connect to my modem/router and NTE5 master socket?
I will be using CAT5e cable, and connecting the a jack at each end.
Also what is the wiring configuration for the jacks? blue, bluewhite etc etc.
regards,
silvryn
Administrator MrSaffron
(staff) Wed 25-Mar-09 22:24:43
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: silvryn] [link to this post]
 
And NTE5 master socket does not accept an RJ11 plug, if we are talking of a normal telephone socket.

Or do you have a faceplate with telephone and ADSL sockets? So yes an RJ11 plug is what you use, and you would need the appropriate crimp tool if making up your own lead.

Wiring its the centre two pins that are used and just use the two wires from one pair in the CAT5 bundle. Getting a RJ11 plug to clamp down on the outer of a 4 pair CAT5e cable may be difficult, the usual recommendation would be to use cable that is CW1308 spec.

Unless you've a long cable run it may be cheaper and easier to buy a pre-made cable from somewhere like www.adslnation.com

Andrew Ferguson, [email protected]
www.thinkbroadband.com - formerly known as ADSLguide.org.uk
The author of the above post is a thinkbroadband staff member. It may not constitute an official statement on behalf of thinkbroadband.
Standard User silvryn
(learned) Wed 25-Mar-09 23:16:54
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: MrSaffron] [link to this post]
 
Sorry about that. Yes it does have a face plate with phone and dsl socket.
I have all the tools to connect the plug, I just need the wiring info so I can proceed.
I was thinking of getting 6p6c plugs to do the job. Of if it is possible, i could buy an rj45 to rj11 adapters. I could then wire up a standard rj45 cross over cable at both ends and then put the adapters on each end. Therefore making the whole thing easier to deal with. If that is possible of course.
Thanks for the reply MrSaffron


Register (or login) on our website and you will not see this ad.

Administrator MrSaffron
(staff) Thu 26-Mar-09 09:53:11
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: silvryn] [link to this post]
 
The socket on the ADSL faceplate will accept an RJ45 plug, and if the wiring follows usual CAT5 wiring i.e. one pair on the centre two pins then a normal CAT5 cable should be fine.

At the modem end you would need the plug to be an RJ11 plug, and the adapters may be an easy solution if you have an existing pre-made RJ45 terminated cable.

Andrew Ferguson, [email protected]
www.thinkbroadband.com - formerly known as ADSLguide.org.uk
The author of the above post is a thinkbroadband staff member. It may not constitute an official statement on behalf of thinkbroadband.
Standard User silvryn
(learned) Mon 30-Mar-09 19:25:41
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: MrSaffron] [link to this post]
 
Hi,
sorted out the wiring. And my side is sorted and the LAN is running at 93% speed. But my Internet is slow. I believe this is because BT are trying to find a fault, as I contacted my ISP and they said they have put in a fault report with BT.
The reason for reporting this fault is that the connection is slow or disconnecting at random times. Although I believe it to be throttling of my connection, but it has progressed further with my downspeed and upspeed being slashed. Whether this is the ISP or BT I don't know.
I was getting 6.9Mbits down and 380 up.
I'm now getting under 1Mbit down and 288 up.
I've tried 3 seperate modem/routers of different manufacter and they all report not being able to ping the default gateway.
When I signed up, they advertised I would be on their network, but after conferring with their Tech support, I now know that my exchange needs to have their equipment in it. Which it doesn't, and that I am on BT Ipstream. Which is not clearly advertised.
I have been given every excuse under the sun and I have countered their excuses at each turn. To which I get a moment of silence, as they know they have been caught out on more than one occassion.
I could go into the excuses, but they have been written about by numermous people on here and therefore not worth typing up.

You may have noticed I have not mentioned who my ISP is. I've done this purposely because it may well be a fault in the end. But I am fed with waiting for the fault to be sorted. As it has been over 3 weeks.

So I'm stuck as to what to do next.
Any constructive suggestions would be helpful.
Standard User deleted
(deleted) Mon 30-Mar-09 21:48:00
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: silvryn] [link to this post]
 
In reply to a post by silvryn:
I was getting 6.9Mbits down and 380 up.
I'm now getting under 1Mbit down and 288 up.
288Kb Upstream is indicative of a fixed ADSL product, rather than ADSL Max.
What speed are you syncing at?
Can you post you router stats?

Edited by deleted (Mon 30-Mar-09 21:48:54)

Standard User silvryn
(learned) Tue 31-Mar-09 21:21:05
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: deleted] [link to this post]
 
Here are my line stats from my Thomson Speedtouch 546 v6. As you will see the router/modem hase been on for 1 hour and you will see the speed has been reduced even further. I'll let you interpret the rest.


DSL Connection

Link Information

Uptime: 0 days, 1:00:34
Modulation: G.992.1 annex A
Bandwidth (Up/Down) [kbps/kbps]: 288 / 1,504
Data Transferred (Sent/Received) [KB/KB]: 0.00 / 0.00
Output Power (Up/Down) [dBm]: 12.0 / 17.5
Line Attenuation (Up/Down) [dB]: 31.5 / 44.0
SN Margin (Up/Down) [dB]: 7.0 / 11.5
Vendor ID (Local/Remote): TMMB / TSTC
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 7,921
CRC Errors (Up/Down): 0 / 7
HEC Errors (Up/Down): 0 / 3

Just to add one more thing. I have used 2 other modem/router made by different companies and they come up with the same results.

I have Cisco engineer coming in on Friday to test my network and telephone system to make sure it is not an internal problem.
I have had this problem with my last ISP (tiscali...bunch of con merchants as long as they have been in business......now the noose has finally tightened around their necks laugh ) and now UK Online. Before the Pipex user database was bought out by Tiscali, I had a perfect connection for 3 years which went through the same exchange using BT IPstream.
I could go on and on, but what's the point. I want out only after 4 months.
Administrator MrSaffron
(staff) Tue 31-Mar-09 23:32:27
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: silvryn] [link to this post]
 
With upstream affected like this it is usually seen when there is a wiring issue, e.g. not use twisted pair, but rather legs from different pairs for the wiring ( a possibility with the CAT5 wiring short cut )

Odd to see upstream attenuation so high compared to downstream, it is normally half. Your Ethernet network should make no different to the ADSL, but the fact you are talking of a telephone system makes me wonder.

Even when you say it was working fine at 3Meg, that is seriously slow for a 44dB attenuation line, i.e. this problem may have been around for a while, and the BT Wholesale systems have just slowed you down to try and stabilise a problem and/or reduce the number of errors.

Andrew Ferguson, [email protected]
www.thinkbroadband.com - formerly known as ADSLguide.org.uk
The author of the above post is a thinkbroadband staff member. It may not constitute an official statement on behalf of thinkbroadband.
Standard User silvryn
(learned) Mon 06-Apr-09 19:03:40
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: MrSaffron] [link to this post]
 
Ok, here's an update.
The Cisco engineer ( a m8 of mine) replaced the Micro Filter faceplate on the Master nte5 socket and the noise on the line went significantly down and after about an hour the speed returned to 6.9Mbits down and 380up. This was done last Friday (3rd April) and I decided not to reboot the router/modem and the connection was at full speed over the weekend.
But today I did a speed test this morning and the speed was once again over 6 Mbits/380up, then I did a test only a few muniutes ago (6.34pm) and the speed has dropped again to around 2/3Mbits. The upstream has not been affected.
I can only think that the line is being throttled or packet shaped. My ISPs tech say this is down to congestion, but I have asked other people who use different ISPs and are all on BT IPStream, and they say they have no slow down at night. Am I being paranoid or could I be correct?
Here are my line stats from my Thomson ST 546v6

Uptime: 1 day, 9:59:05
Modulation: G.992.1 annex A
Bandwidth (Up/Down) [kbps/kbps]: 448 / 8,096
Data Transferred (Sent/Received) [KB/KB]: 0.00 / 0.00
Output Power (Up/Down) [dBm]: 11.5 / 19.5
Line Attenuation (Up/Down) [dB]: 11.0 / 18.0
SN Margin (Up/Down) [dB]: 28.0 / 16.0
Vendor ID (Local/Remote): TMMB / TSTC
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
Loss of Link (Remote): 0
Error Seconds (Local/Remote): 0 / 0
FEC Errors (Up/Down): 0 / 40
CRC Errors (Up/Down): 0 / 0
HEC Errors (Up/Down): 0 / 0
Standard User Rockh
(eat-sleep-adslguide) Mon 06-Apr-09 20:28:19
Print Post

Re: Wiring an RJ11 cable for dsl modem?


[re: silvryn] [link to this post]
 
Your sync stats are almost as good as it gets, slightly down on full smoke (8128) for the downstream.
I'd put the slow speeds down to congestion on your isp's backhaul / network.

Dave
Pages in this thread: 1 | 2 | (show all)   Print Thread

Jump to