|
|
|
I am using wireless for the first time the last few weeks on my laptop, my pc's still go over wired as well as my xbox. My wired is constant sub 1ms with no packet loss however my wireless is all over the place. I have already tried channels 1,6,11 results below.
Channel 11 - currently using - latency between 1ms and 110ms, packet loss over 100 pings averaged at 4%, average latency 6ms.
Channel 6 - latency between 1ms and 320ms, packet loss over 100 pings at 26%, average latency 19ms.
Channel 1 - latency between 17ms and 670ms packet loss over 100 pings at 49%, average latency 109ms
there is 4 other routers in the vicinity, the 2 BT ones have a strong signal according to windows 5 bars, my own router which is only 2 metres away from the laptop has 3-4 bars on channel 11 and 1-2 bars on channels 1 and 6. 3 sky routers are weak, indications are heavily powered BT routers are causing interference on other routers?
netstumbler app doesnt work says invalid wireless hardware.
Is there generic tips like mtu adjustment etc. that is reccomended for wireless use? Web browsing seems fine but using things like ssh which is very latency sensitive is aweful on my laptop.
|
|
|
|
You want to try and get a free channel, particularly if other devices are showing strong signal on a given channel. Ideally your channel would be 4 or 5 channels away from any neighbours (e.g. 1, 5, 9, 13) for negligible frequency overlap, but any space is likely to be better than sharing a channel. If 1, 6 and 11 are all in use by other devices, you could try channel 13 and perhaps also channel 9.
|
|
|
netstumbler app doesnt work says invalid wireless hardware.
Give Inssider a try instead. I find it much more useful than Netstumbler.
|
|
Register (or login) on our website and you will not see this ad.
|
|
|
just tried 13 is worse than 11
|
|
|
|
I bet if you move the router 2 inches to the left, and repeat the tests, you'll get entirely different readings. Signal reflections can cause peaks and dead spots in a room, and changing the frequency changes the positions of these spots, because the wavelength changes.
|
|
|
Hi, I found info on Wi-Fi standards useful and now use only the faster 802.11g standard.
Note: In the U.S. and other countries with similar regulations (channels 1, 6, 11, with 25MHz separation),
and four in Europe (channels 1, 5, 9, 13, with only 20MHz separation).
http://en.wikipedia.org/wiki/IEEE_802.11g-2003
|
|
|
the 2 BT ones have a strong signal according to windows 5 bars,
Is you laptop using an N rated wireless adaptor ? If so, the BT routers may well be version 2 Homehubs, which will be transmitting an N rated signel, hence your lappy will 'see' it as stronger.
|
|
|
If you want a nice simple small (less than a 100KB in total when unzipped that doesn't need installing, just unzip it and run) program for monitoring wireless in your area, have a look at WirelessNetView from Nirsoft;
http://www.nirsoft.net/utils/wireless_network_view.html
If you scroll down there is also a section named Company Name that has a download that will give you the makers name of each access point though it is not necessary.
It's not as pretty as Inssider, just giving a list view but I like it because it doesn't need installing. But it will still show you the wireless networks in your area with signal strength and channels used by each plus a lot of other info. You can then at least try and fit yours between the others in any unused channels to try and maximise your signal. As someone else said up thread, it is always worth moving your access point around as even inches in any direction, including up and down can make a significant difference in your signal strength. Even the angle of the aerial on your access point can help or hinder, both in reception of wanted signal as well as rejection of unwanted signals.
BTW, if you are using Vista, get the Wireless Network Meter gadget from Addgadget.com. NOTE; the link below is a direct download link for it and it is a 96KB zip file:
http://addgadget.com/download/Wireless_Network_Meter...
This will allow you to easily monitor your signal strength in real time as you move your access point around and try different channels. I rarely lose more than two or three milliseconds using wireless compared to wired. E.g. I get 17-19ms to the beeb when wired and rarely more than 19-21 on wireless anywhere in my flat. Add 10-20ms very worse case if I am at the other end of the block of flats from my access point, a BeBox ST780W.
|
|
|
|
thanks guys I havent had time to try insider or this app yet, and I may try moving my router around but its in an ideal spot and I dont want to move it too much.
No idea if the wireless card in the laptop is N rated or not.
As soon as possible will try what you said, possibly tommorow.
|
|
|
|
FYI: Use Device manager and double click on the Wireless card entry and then usually the Advanced tab to check what speeds/modes your wireless card has. It is always advisable for best performance, as long as of course you don't need a multi-speed network (e.g. a and/or b and/or g etc), to lock all your kit to one speed rather than leaving any of it on auto or multi-mode. Auto or multi-speed being the usual default setting for new or untouched kit, including routers.
|