Technical Discussion
  >> Technical Issues


Register (or login) on our website and you will not see this ad.


These posts have been archived and can no longer be replied to or modified.
  Print Thread
Standard User novice20
(newbie) Sat 09-May-09 22:12:39
Print Post

No dial tone


[link to this post]
 
I'm helping a computer illiterate friend who's just moved house. They've had their broadband connection moved to the new house line and been told its OK to use. I've tried to get connected but as soon as the ADSL modem is attached the phones have no ring tone and the modem doesn't connect (Speedtouch, usb green , adsl green flashing.) Error on connection is no dial tone. The phone setup here is extremely dated with the line in going to a junction box (small rounded corner rectangular box.) There are two lines out which go to phone sockets in the hall and bedroom. The input line has 4 wires (light brown, brown, blue and green.) All the sockets have filters and the loss of dial tone doesn't seem to be short term. You get an engaged tone if you try dialing the house number from another phone. Tried different filters but not them. I'm assuming there's a problem with the original phone wiring rather than ADSL but have no idea what the problem might be. Phones work fine when the modem ins't connected.

Edited by novice20 (Sat 09-May-09 22:37:28)

Standard User deleted
(deleted) Sun 10-May-09 10:01:06
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
That does sound like a fundamental wiring fault.

This is the guide I always refer people to for sorting out wiring,

http://www.wppltd.demon.co.uk/WPP/Wiring/UK_telephon...

you'll also need to translate between the old and new colour codes,

http://www.diynot.com/forums/viewtopic.php?t=174903

about halfway down has the info you need.
Standard User peepoil
(committed) Sun 10-May-09 10:10:47
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
You should only have 2 wires not 4.
One of these was for the old fashioned bell and is notorius for causing problems and bad connections for computers. There are instructions on this site on its removal.
I think I read that the fourth wire was for a mini exchange type system and should also be removed.
Sounds like a very old configuration try contacting BT (if you are on BT) and explain what you have and ask for a new junction box, they may fit one free if the one you have (which is theirs) is no good otherwise they fit the new ones fairly cheap.

If you do get a new one make sure you tell the engineer that you want him to connect only the 2 wires.
The wiring from the box inside the house is yours disconnect the extra wires as they can act as an ariel causing problems.


Register (or login) on our website and you will not see this ad.

Standard User deleted
(deleted) Sun 10-May-09 12:22:34
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
Sounds like a simple case of a faulty modem to me.
Standard User peepoil
(committed) Sun 10-May-09 16:18:51
Print Post

Re: No dial tone


[re: deleted] [link to this post]
 
In reply to a post by RandomJointer:
Sounds like a simple case of a faulty modem to me.

Yes, I got sidetracked by your wiring description, but first get hold of another modem or router and check if that works. If not have your ISP check the line.
You would still be well advised to sort out the wiring, there is a guide posted below.

.
Standard User gomezz
(eat-sleep-adslguide) Sun 10-May-09 16:35:28
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
In reply to a post by novice20:
Phones work fine when the modem ins't connected.
Have you tried the modem with nothing else (no phones, no Sky box, no security alarm) plugged in?
Standard User novice20
(newbie) Sun 10-May-09 17:25:18
Print Post

Re: No dial tone


[re: gomezz] [link to this post]
 
Yes, tried that but same result.

As regards the wiring I think I must have missed a box somewhere on the line in. With the 4 wires line input there didn't seem any hardware to generate a ring signal on the junction box I looked at inside the house so maybe I missed one outside which is the initial line in, I'll check that.

The modem should be OK as its the same modem they used before the house move, but that doesn't prove anything so I'll see if I can test it elsewhere.

Thanks to you all for the help.
Standard User Zarjaz
(knowledge is power) Sun 10-May-09 19:21:55
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
Simple, either the modem or one of the micro-filters, has a loop fault on it. Identify the faulty piece of equipment, and replacement.

Administrator MrSaffron
(staff) Tue 12-May-09 14:34:55
Print Post

Re: No dial tone


[re: novice20] [link to this post]
 
1. With no ADSL modem connected, does the telephone line work fine?
2. The no dial tone reported by the ADSL modem, does not really mean no dial tone, it actually means it cannot lock onto an ADSL signal, either the line is not enabled, or signal is too weak, or modem is broke.

You need to try a different modem, and if the line is a long one a good chance the issue is that the wiring is not helping.
It is also a 50/50 that the broadband has not successfully being moved to the new property, once we know which provider a better idea of the probability becomes possible.

Andrew Ferguson, [email protected]
www.thinkbroadband.com - formerly known as ADSLguide.org.uk
The author of the above post is a thinkbroadband staff member. It may not constitute an official statement on behalf of thinkbroadband.
  Print Thread

Jump to