Cann't boot to offical Windows 7 install disc in BIOS?

I tried to clean install Windows 7 Professional 32-bits to replace my existing XP Prof in BIOS Environments, which is currently using an Asrock's Conroe1333-DVI/H R2.0 OLD motherboard without success! I could configure the MB to boot from my DVD Drive but, despite it can boot into either Linux Boot Discs or even the original XP Pro install discs, it just cannot boot my Windows 7 Professional FULL install disc at all. My DVD Drive just flashed a few times and my PC then came into a total freeze, i.e. no HD activities nor any signs of my Windows 7 FULL install disc activities IF I inserted my Windows 7 Pro FULL install disc into the DVD Drive and rebooted.
However there is nothing wrong with my Windows 7 FULL install disc because I had tried it on another PCs, two of them alternatively, and it booted alight in each case. So there is something "unique" in my Asrock PC which just refused booting into this Windows 7 disc. This Windows 7 FULL disc is genuine and has its only Product Key, which remains un-used at the moment. Any one may have some suggestions???
To be honest I'm suspecting the Asrock's MB Firmware may take a part in that but UNTIL it is proven most likely, I don't want to flash my MB's FW as it could be damaging IF I did it wrongly!!!
To be honest I am suspecting the Asrock's MB

if its a modern rig try making sure you are not using uefi boot.

Just looked the Asrock site, latest firmware is v2.10. What's the current version on the m/b?

Since the symptoms point to a compatibility issue, you should upgrade the BIOS to the current version. Unless you're very unlucky and get a power cut when writing, the upgrade should be straight forward.

What is "uefi boot" may I asked??
Thanks for the reply!

UEFI Boot

Thank you for the reply! I did look into Asrock's web-site as well. My current MB's FW is P2.0 which has never been flashed since the day I bought it couple of years back. Their latest corresponding MB FW is R2.10, which I believe is NEWER than my existing one already on my MB.
It seems like the only way to find out is to flash my MB FW to this latest R2.10 as suggest by yourself, and been thinking about it myself!!
Just to find a suitable time as my wife is using it constantly to view her internet stuff...

It sounds like you have a problem with the DVD drive. Try another DVD drive if you can.

Thank you for the info.. I should have consult the "Google"!!!

The DVD Drive is brand-new and has been booting O.K in various Linux, and even Windows XP install DVD, bootable DVDs from the same PC. So it is most likely SW/FW related for my problem.
Thanks

This probably not related but on another forum a poster had a similar issue and fixed with the following:

I figured out my problem,
I connected my monitor using HDMI, which was not good for windows 7 installation.
I went and bought a DVI to VGA adapter and cable and it installed fine.

Are you using HDMI by any chance?

It is NOT a modern rig since it is at least 4-5 years old motherboard! I am sure that it has been booting into BIOS format.
Thank you

Well my PC's graphic output connector is DVI and the other end connected to my TV is HDMI. So, yes, I'm using the HDMI port of my TV. But firstly I haven't got a VGA graphic O/P from my TV, except HDMIs, and secondly I would like to maintain BETTER graphic than just VGA by keeping the HDMI connection. For my issues, I think it is NOT the graphic HDMI interface been causing my misery because there was absolutely NO ACTIVITIES in my PC from neither the DVD drive's LED nor the HDD's LED at all.
Thanks

In reply to a post by OCdragon:

The DVD Drive is brand-new and has been booting O.K in various Linux, and even Windows XP install DVD, bootable DVDs from the same PC. So it is most likely SW/FW related for my problem.
Thanks

Everything in your OP indicates that the DVD drive in your ASRock system does not like your Windows 7 installation disk for some reason. If I were you, I would swap out the DVD drive, even if you have to nick one from another system as a test. It's a lot simpler and safer than re-flashing your motherboard. Microsoft's Compatibility Centre lists the Conroe1333-DVI/H as being Windows 7 compatible.

The fact the your DVD drive can read other installation media and that other DVD drives can read your installation disk does not rule out the possibility that your disk is below spec. and your drive cannot handle it although others can. Still, you seem pretty certain about what is not causing the problem so I'll leave you to find out what actually is.

Thank you for the suggestion. Previously I did swap out my DVD Drives while my 1st DVD was showing exactly the same symptoms. Then I swapped it with the existing brand-new DVD Drive, which unfortunately is showing exactly the same symptom too! That is why I am suspecting that my Asrock MB keeps failing to boot to my Windows 7 disc is "unique" to my Asrock MB, possibly its FW....................
Very frustrating

I have finally tracked down to WHAT was causing my above problem! It was NOT the DVD Drive nor my MB's FW needed updating! It was my DVI-D interface from my graphic card to my TV's HDMI interface causing this problem! Whenever I connected my above PC's DVI-D port, which looking to support HDCP (High-Definition Control Protection), to my TV's HDMI port it would freeze up my PC whenever I was attempting to boot into my Wndows 7 install disc or even attemping to run W7. However I could install Windows 7 as NORMAL if I switched to my PC's VGA interface and used my TV's RGB port instead. My PC would also freeze even if I had installed and running normally with Windows 7 using VGA connections but switching to above DVI-D to HDMI interconnections afterwards!! So,. yes, it was my DVI-D to HDMI interface been causing my above problem for windows 7. As for WHY I just don't know.....Could it be the "HDCP" signal causing it in W7 ?????
Did some one run Windows 7 with their DVI-D and HDMI interfaces successfully????

Thanks for all your previous suggestion as it was quite difficult to track down until some one suggested the possible issues with HDMI interfaces.

P.S: My old Windows XP Pro was running perfectly normal with this DVI-D to HDMI connections previusly!

You might find that if you can get it installed using a different monitor that once the drivers are all on that it would probably work with the HDMI. The problem may just be that the boot media doesn't work with the config but that Win 7 could well be fine.

I have had hdmi out and dvi out on my cards for over 6 years with no problems installing with hdmi and dvi at same time(apart from the fact it clones the picture on both screens so I normally have hdmi tv turned off when installing)

A way of doing it is if its a older version of W7 get a latest version legally obtainable online to download.

I believed my Windows 7 Pro disc is a legal one despite it displaying Dell's logo in the Administrator ICON after installation. Just forgot to say that my MB came with its PCI-E DVI-D extended card (Asrock-1333 DVI/H R2.0) and I had to plug that card in to get DVI-D output, which was causing me the said problem UNLESS I switched to the MB's on-board VGA output. I have just ordered a separate DVI & HDMI PCI-E graphic card and will use that instead when it arrives, hoping that my DVI-D problems were due to "incompatible HW" issue of that Asrock's extended DVI card.
Just a few moree days I will find out!!!!