@cjn

This is the first time, I've seen info on Zen's Digital voice, many just state they'll not give the information, I would be interested in why you stopped using it ?

einsateinagogo

can you not use a Gigaset N300A DECT base and settings as per here

https://www.zen.co.uk/help-support/general-sip-settings

which is what @cjn confirmed, and then you don't have to use the Fritzbox

Edited by einsteinagogo (Sun 19-Feb-23 19:32:22)

@cjn
This is the first time, I've seen info on Zen's Digital voice, many just state they'll not give the information, I would be interested in why you stopped using it ?
einsateinagogo
------------
I didn't stop using it; I started with the 'correct' route via the Fritz!Box and its FON port, but I had a couple of other SIP providers already programmed into the N300A so I just wanted to try Zen DV by the same method.

They both seem to work so it doesn't seem to matter which one to use. One point in favour of the 7530AX/FON is that it gives a simple way to block and divert incoming calls.

The connection info was already established for me in the Fritz!Box, where I could read the server address in plain text, and I found the password by idly browsing my portal.

Edited by cjn (Sun 19-Feb-23 22:09:56)

can you not use a Gigaset N300A DECT base and settings as per here
https://www.zen.co.uk/help-support/general-sip-settings
which is what @cjn confirmed, and then you don't have to use the Fritzbox
Edited by einsteinagogo (Sun 19-Feb-23 19:32:22)
--------
Yes, but this doesn't supply the PW, or what I believe is the correct server address. This info is only found by 'investigation'.

Edited by cjn (Sun 19-Feb-23 22:10:55)

Thanks for the pointers, cjn.

With your help I've managed to get asterisk/pjsip to talk to Digital Voice. For the record my settings are:

[zen]
type = wizard
sends_auth = yes
sends_registrations = yes
remote_hosts = voip2.zen.co.uk
outbound_auth/username = <zen phone number>
outbound_auth/password = <passwd>
endpoint/allow = !all,ulaw,alaw
endpoint/context = default
identify/match = voip.zen.co.uk

Make sure you've opened the SIP and RTP ports as per the zen general sip settings page (incoming SIP is from voip.zen.co.uk, NOT voip2).

Also make sure you've unset all CALLERID parts except for the CALLERID(number), which must be your zen phone number.

Hope this helps someone else.

Tim

Anybody knows what other makes of the phones could possibly work?
Every SIP capable phone?
ie Yealink W76P

sebus

Edited by sebus (Fri 24-Mar-23 07:57:29)

I have W70B with W56H
The unit shows as Registered with Zen using the info from support @ AA

https://support.aa.net.uk/VoIP_Phones_-_Yealink_DECT

Had to register WITHOUT +44 (just the number)

But cannot make/receive any calls

Outgoing phonecalls "Global error" on W56H
Incoming gives an error to the dialing user: "Phone is currently unavailable"

So no idea if something is missing from config, or the line is not yet fully configured on Zen end.

I just find the Zen support being total idiots, so hardly can get a reply from them, especially that they only "support" only own router - that I do not care about)

sebus

Edited by sebus (Sat 08-Apr-23 14:13:22)

I am getting 603 Declined while trying to make a call

No idea why N300A works and Yealink does not

Anybody any idea?

Seb

What CODEC are you using on the yealink? AFAIK AA only support g.711 alaw

Zen also only support g.711Zen SIP settings

Edited by wiggsc00 (Fri 14-Apr-23 12:25:54)