got no extensions took the front of to test yrs ago never put it back on ill try a reboot with corded phone out see if it makes adiffence ?is there a newer firmeware than the
Software Release: 6.2.29.2
is that the only firmware? been runing roterstats for 1 hr flat line on 6 not moved

Link Information


Uptime: 0 days, 0:00:04

Modulation: G.992.5 annex A

Bandwidth (Up/Down) [kbps/kbps]: 667 / 2,795

Data Transferred (Sent/Received) [KB/KB]: 0.00 / 0.00

Output Power (Up/Down) [dBm]: 9.5 / 17.0

Line Attenuation (Up/Down) [dB]: 14.0 / 27.0

SN Margin (Up/Down) [dB]: 8.0 / 6.5

Vendor ID (Local/Remote): TMMB / IFTN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 0 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 0 / 0

HEC Errors (Up/Down):
this is the reboot with phone out????????????????????????????????



Uptime: 0 days, 0:00:35

Modulation: G.992.3 annex A

Bandwidth (Up/Down) [kbps/kbps]: 1,019 / 8,279

Data Transferred (Sent/Received) [KB/KB]: 670.00 / 74.00

Output Power (Up/Down) [dBm]: 12.0 / 0.0

Line Attenuation (Up/Down) [dB]: 14.0 / 26.5

SN Margin (Up/Down) [dB]: 10.0 / 6.5

Vendor ID (Local/Remote): TMMB / IFTN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 0 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 32 / 0

HEC Errors (Up/Down): 7 / 0

Edited by deleted (Sat 02-Oct-10 14:56:39)

This version of DMT may work with your modem. http://www.2cent.de/dmt/v7/dmt.zip

It would let you visualise the noise on your line.

Time to reboot again...

Router has synced to the 6dB target margin, but somehow picked a low sync speed.

Need another rotuer on line to rule out bugs with the speedtouch.

Link Information


Uptime: 0 days, 0:00:49

Modulation: G.992.5 annex A

Bandwidth (Up/Down) [kbps/kbps]: 191 / 2,975

Data Transferred (Sent/Received) [KB/KB]: 6.00 / 10.00

Output Power (Up/Down) [dBm]: 9.5 / 0.0

Line Attenuation (Up/Down) [dB]: 14.0 / 27.0

SN Margin (Up/Down) [dB]: 21.0 / 24.5

Vendor ID (Local/Remote): TMMB / IFTN

Loss of Framing (Local/Remote): 0 / 0

Loss of Signal (Local/Remote): 0 / 0

Loss of Power (Local/Remote): 0 / 0

Loss of Link (Remote): 0

Error Seconds (Local/Remote): 0 / 0

FEC Errors (Up/Down): 0 / 0

CRC Errors (Up/Down): 32 / 0

HEC Errors (Up/Down): 7 / 0
now this again wats up line or exchange?

Speedtouch firmware can be found here.

which firmware is the best tested one? any recommendtions?

Can't say which from the data

getting error canot up grade firmware have the internet got to be unpuged or iam i doing something wrong?

I always used to disconnect and reset the kit to defaults before upgrading firmware, just remember to backup the config before you start.
Are you using the upgrade wizard that's on the cd ??

Not played with a speedtouch for a while though I've got a couple in the cupboard and an O2 one providing my connection but it's in bridge mode.